Working Principle of a Plastic Mixer Machine Explained

share:
Nov 4 2026

A plastic recycling line turns used plastic into uniform pellets through shredding, washing, drying, melting, filtering, and pelletizing. Between these steps, the material often needs blending and moisture control. That is the job of a 3 ton vertical plastic particle mixer with drying function.https://www.yudemachinery.com/vertical-plastic-particle-mixer-with-drying-function/3-ton-vertical-plastic-particle-mixer-with-drying-function A vertical spiral lifts pellets from the bottom, lets them fall along the barrel wall, and passes hot air through the moving batch. This action mixes color and additives while it removes surface moisture before extrusion, injection molding, or film blowing. Below, I explain each step, the main parts, and the checks I advise before you buy.

3 ton vertical plastic particle mixer with drying function

Where a 3 Ton Vertical Plastic Particle Mixer with Drying Function Fits in Recycling

Why Moisture and Uneven Mixing Cause Defects

You can get sick from both new and recycled pellets, but recycling pellets change more from lot to lot. To keep water on top, pellets can be used. In a big batch, masterbatch or chemicals can settle in different spots. When water is put into an extruder or injection barrel, it turns into steam. This can cause the product to bubble or have silver streaks on it. If the color or filler isn't even, the pipe, profile, and film may have different shades. It takes a lot of work to reuse things. According to the OECD's Global Plastics Outlook 2022, only 9% of the world's plastic trash was recycled in 2019. The U.S. Environmental Protection Agency (EPA) says that about 8.7% of the plastics found in U.S. municipal solid waste were recycled in 2018. When the feedstock is cleaner and more regular, more things can be turned into useful things.

Batch Capacity Versus Hourly Output

There is no hourly rate for the 3 ton vertical plastic particle mixer with drying function. Instead, there is a batch rate. It can hold up to 3000 kg and has a bulk density of 0.6 to 0.8 g/cm³. It takes 30 to 45 minutes to mix and dry one cycle. To get an idea of the hourly output, divide the batch weight by the full cycle time, which includes loading and unloading. Then, make any fill level changes that are needed. An extrusion line that makes a lot of pipes or shapes might need more than one batch per shift or a bigger tank. Yude Plastic Machinery makes a vertical plastic mixer that can hold between 600 kg and 10 tons, so it will work with your line.

Key Specifications at a Glance

Between 4,500 and 4,800 liters is the right amount. At least 98% of the mixing must be even, and at least 0.5% of the dried material must still be wet. The mixing motor can handle 22 to 30 kW of power, and the electric heating tubes can handle 60 to 75 kW. You can also use steam to heat the room. The hot air can go from being room temperature to 85°C. Pieces of PE, PP, ABS, and PVC can be changed colors, mixed, and dried in this 3 ton vertical plastic particle mixer with drying function. It's easy for your tech team to compare quotes from different businesses with these numbers.

The Working Principle Step by Step

Step One: Loading and Spiral Lift

The material comes in through the serving hole, whether it is loaded by hand or fed by a moving system. Hot air won't be able to escape because the port is sealed. More carbon steel coils inside the barrel move the pellets from the bottom to the top. After that, the stuff falls back down along the barrel wall. Because it moves up and down, each ball goes through the batch many times. Color masterbatch and chemicals tend to stick to some parts of the load in a still hopper. This way, they don't spread out over the whole load. This one path of flow mixes and moves heat around in a 3 ton vertical plastic particle mixer with drying function.

Step Two: Hot Air Drying and Moisture Removal

The hot tubes warm the air, and the circle moves the batch. Hot air, up to 85°C, flows through the moving pellets and evaporates any water that is on the surface. Because there is insulation on the barrel, more heat stays inside the vessel. There is no way for one spot to get too hot for too long if the pellets are always moving. This is important for resins that don't like heat, like PVC. The goal is for the level of moisture to be 0.5% or less when it's dry. Most of the water on the surface is blown away by hot air. A dehumidifying dryer is needed for many plastics, like PA and PET, because the pellets hold water. This 3 ton vertical plastic particle mixer with drying function can dry things in the first step.

Step Three: Discharge and Batch Control

Someone opens the discharge port after a certain amount of time, which is commonly 30 to 45 minutes. This could be an extruder hopper, a granulator feed, or an injection molding line. Once the batch is ready, it moves on to the next step. The material is moved only once by the 3 ton vertical plastic particle mixer with drying function. It is not sent to a separate mixer and dryer. This is because the same vessel is used for both mixing and drying. That gets rid of places where dust or other things could get in. The people in charge decide how long and how hot each resin should be. So that the same method is used for every batch, I think you should write down the settings for each kind of resin.

Main Components and Build of the Mixer Dryer

Barrel and Mixing Spiral

GB/T 700 says that the barrel is made of Q235 carbon steel, which is a construction type that is widely used in China. As well, it has a layer of padding on top of it. The strong carbon steel spiral can hold its weight with a 3000 kg load. It holds between 4,500 and 4,800 liters, which is a good amount of space for the pellets to move around in. Carbon steel can be mixed with most types of PE, PP, ABS, and PVC particles. Early on, let our engineers know if you use rough compounds or need a different contact material. That way, we can talk about how to make a solution that works for your recipe.

Drive and Heating System

A 22–30 kW motor turns the circle. Choose the grade based on how dense the material is and how much it weighs in a batch. Electric heating tubes put out 60 to 75 kW of power. Plants that already have a steam source can use that instead of the electric heating tubes. More heater power cuts down on the time it takes to warm up, but the voltage, cable size, and breaker rating must be right. Please let us know what the power and phase are in your area before you buy a 3 ton vertical plastic particle mixer with drying function. Yude Plastic Machinery can change its tools to fit the needs of the local business world. A US company should talk to a professional electrician to find out what kind of electricity it needs.

Sealing, Safety, and Quality Control

The sealed feeding port keeps the heat inside the barrel by not letting hot air out. There should be alarms for hot surfaces, a circle that spins, and a lot of power. For those who want to buy something, safety features such as guarding, emergency stops, and overload protection should be written down and asked for. Not only that, but they should also check these details against US laws such as the National Electrical Code (NFPA 70) and the OSHA machine guarding rules (29 CFR 1910.212). When raw materials come in, Yude Plastic Machinery checks them. They also keep an eye on the production process and test each finished machine before sending it to a customer. Ask for the inspection records along with your price.

How the Mixer Dryer Compares with Other Methods

Vertical Versus Horizontal Mixers

It takes up less room on the floor, and the material moves around more easily because it falls along the barrel wall. It's best to use a horizontal mixer in plants that can't have very high ceilings or that already have horizontal lines for moving things. Before you buy a 3 ton vertical plastic particle mixer with drying function, make sure the barrel can clear the roof and there is room for people to feed it. Find out how wide the door is, how high the ceiling is, and how far the forklift or crane can reach. Too little floor room can make it hard to work in pipe and profile shops with lots of extrusion lines. If the seller only gives you a simple plan picture, you might not have to pay a lot to make changes after the deal is done.

Hot Air Mixer Dryer Versus Dehumidifying Dryer

When air is dried in a dehumidifier, the desiccant makes it very dry and low in dew point. This is the best choice for engineering plastics that soak up water, like PC, PET, and PA. Hot air flow works best when the outside of the PE, PP, ABS, and PVC particles is wet. The batch is also mixed. Heating doesn't dry things well on its own because the water has to leave the vessel with the air. If you work with nylon, this 3 ton vertical plastic particle mixer with drying function is good for pre-drying it. After that, you should finish the job in a dryer that gets rid of moisture. You can find out which way works best by testing pellets on your own.

Integrated Versus Separate Equipment

The container has a 3 ton vertical plastic particle mixer with drying function. It can mix colors, change them, and dry them out. That means you won't have to move things as often, which means they will be less likely to get dirty. You can do more when you have separate machines. It is possible for one batch to be dried while another is mixed, and for one stage to become bigger without having to change the other. Single pots work best for plants that don't need a lot of space and need to change their food often. Some plants may run more than one barrel or add a separate dryer if they need to keep making a lot of things. First, write down your daily batches, changes to the recipe, and free space.

Selecting, Testing, and Buying the Right Machine

Match the Machine to Your Business

Different people need different things from a machine. An extruder for pipes and profiles needs a lot of input that is steady and regular. Differences in shade cause products to be thrown away, so color uniformity is important. Some recipes may need a certain spiral or volume, and compounders and modifiers need to be able to mix and change colors. Distributors need tools that can handle changes in more than one language and follow local rules. As a partner, Yude Plastic Machinery helps people in over 30 countries do this. Before you start any job, you need to choose the right 3 ton vertical plastic particle mixer with drying function size based on the resin, batch weight, and line speed. No matter what size you need or what kind of material you want to mix, our R&D team can do it.

Run a Material Test Before You Order

Ask the service to do a test run after sending them sample pellets, regrind, or masterbatch mixes. Make sure the final moisture, steady temperature, full discharge, and cycle time are all checked. Write down the goals that everyone agrees on. For a 3 ton vertical plastic particle mixer with drying function, these numbers are a good place to start: At least 98% of the time, mixing must stay the same, and the mixture must have no more than 0.5% water. Also, you should make sure that each glue has its own range of temperatures. Ask for a movie of the factory test, the working directions, wiring diagrams, and a list of parts that can be replaced. The machine can be checked by a third-party service before it ships if you can't be at the plant.

Common Buying Mistakes

People who buy things always make the same mistakes. Some people think that batch capacity and hourly output are the same thing. Some people choose a machine based only on how well it warms up and doesn't think about how much air it moves or how much it exhausts. A lot of people forget to check the ceiling height and how easy it is to feed. Some people just look at how much the machine costs and don't think about things like lessons, set-up, service, or spare parts. You should think about how much it will cost you in the long run when choosing a 3 ton vertical plastic particle mixer with drying function. Yude Plastic Machinery is open 24 hours a day, seven days a week to help you. For each machine, they keep a record of its service history and keep files on each customer.

Conclusion

Pellets in a machine that recycles plastic need to be dry and mixed well before they can be pushed through a die or shaped. For this, the 3 ton vertical plastic particle mixer with drying function lifts the material with a vertical spiral, moves it along the barrel wall, and blows hot air through the batch. The load is ready to go after 30 to 45 minutes. The information that was made public says that it can hold up to 3000 kg, mix evenly 98% of the time, and have less than 0.5% wetness. Hot air is a good way to get rid of surface moisture, but strongly hygroscopic plastics need to be dried in a dryer that gets rid of moisture. It was also shown that hourly output is not the same as batch capacity. What determines whether a buy is right for a plant is the structure, the electrical supply, the testing of materials, and the total cost of ownership.

3 ton vertical plastic particle mixer with drying function

FAQ

Is a 3 ton vertical plastic particle mixer with drying function rated by hourly output?

Not at all. Three tons is the most weight that can be added at once. To find out how much power is being used each hour, you need to know how long each cycle lasts, how much is being charged, and how fast it is being discharged. Divide 3000 kg by the full cycle time to get a rough idea.

Can it dry nylon or PET completely?

The surface of PE, PP, ABS, and PVC particles doesn't get wet when hot air blows on it. Nylon and PET pellets tend to hold water, so they need to be dried to get rid of the water. Before the clothes go to the dryer, this 3 ton vertical plastic particle mixer with drying function can mix them and dry them.

What should I send with my price request?

Please send the type and grade of plastic, the amount of moisture, the batch size, the target temperature, the mixing formula, the power source, the fitting space, and any automatic needs. When is it going to be sent? What about the service, spare parts, and warranty after the sale?

Could the machine work in a US factory?

Yude Plastic Machinery can make machines that can work with more than one language and meet the needs of a local business. That is possible if you tell us the voltage, phase, and ceiling height. Someone from our team will look at them.

Request a Technical Proposal for a 3 Ton Vertical Plastic Particle Mixer with Drying Function

More than 30 countries buy 3 ton vertical plastic particle mixer with drying functions from Yude Plastic Machinery. The model has a uniformity of 98% or more when mixed and a moisture level of 0.5% or less when dried. Our R&D team can help you make changes to it. We'll help you set it up if you email sales@yudemachinery.com with the type of resin, batch size, and power source. Visit https://yudemachinery.com/ to learn more.

References

  1. Global Plastics Outlook: Economic Drivers, Environmental Impacts and Policy Options, OECD, 2022
  2. Advancing Sustainable Materials Management: 2018 Fact Sheet, U.S. Environmental Protection Agency, 2020
  3. Extrusion: The Definitive Processing Guide and Handbook, William Andrew, 2005
  4. Plastics Additives Handbook, Hanser Publishers, 2009
  5. Principles of Polymer Processing, Wiley, 2006
  6. Plastics – the Facts 2022, Plastics Europe, 2022
Online Message

Learn about our latest products and discounts through SMS or email